11/20/2022 0 Comments Raspberry pi smart home control![]()
The switch now appears on the Things homepage and can be turned on/off with a tap/click exactly as advertised. You can give it a custom name and then save it. I tested this with a Sylvania Smart Plug compatible with the Zigbee IoT standard, which was quickly recognised by the Digi XStick USB stick. You’ll see a '+' in the bottom right corner and the Gateway will scan for available devices, so make sure they’re plugged in. Once set up is complete you’ll be taken straight to the Things Gateway home screen. We’ll start with Zigbee or Z-Wave devices. Zigbee or Z-Wave devices can be added directly, but any third-party system that you connect to via the network, such as Hue lights connected via a Bridge, have to be added in a different way. How you do it depends on the type of device. To make your WebThings Gateway useful, you’ll need to add devices. Finally, create a user account for your system. You’ll need to provide your email address, too, and then confirm your selection via the link in the email that you’re sent. This is the address that you can type into any browser to remote control your home. Next, you need to create your own domain name (). This didn’t work at first, and I had to go into my router’s connected devices section and find the Raspberry Pi in the list to get its IP address. Then fire up a browser and enter this address: and you should connect to the WebThings web management page. The Gateway will connect to your home network and the pop-up will disappear. #RASPBERRY PI SMART HOME CONTROL PASSWORD#Connect to this network ID on your laptop or smartphone and you’ll get a pop-up window asking you to input the SSID and password for your home network. #RASPBERRY PI SMART HOME CONTROL MAC#After a minute or two you should see a Wi-Fi network called “WebThings Gateway XXXX” where XXXX is four digit’s from your Pi’s MAC address. Because this will be operated as a ‘headless’ machine you don’t need to worry about attaching a monitor, keyboard or any other accessories to the Pi. If your Pi doesn’t have Wi-Fi built-in, you can insert a USB Wi-Fi adapter. We used the Digi XStick (ZB mesh version). You’ll also need to insert the Zigbee and/or Z-Wave USB dongles. Before powering it on, you need to insert the SD card loaded with the Things Gateway software. Now it’s almost time to fire up the Raspberry Pi. It’ll take a few minutes, but after that you’ll be good to go. Once you’ve installed Etcher, insert the microSD card into your computer (note: the way I achieved this on my 12-inch Apple MacBook is pretty comical, pictured above but you can also get USB-C card readers).Īll you need to do in Etcher is select the image from your hard drive, select the drive and hit Flash. #RASPBERRY PI SMART HOME CONTROL SOFTWARE#There are many pieces of Mac and PC software that can do this, but I’d recommend Etcher. It can be downloaded from WebThings directly.įrom here you’ll need to flash the software to your clean SD card. #RASPBERRY PI SMART HOME CONTROL DOWNLOAD#The first thing you need to do is download WebThings Gateway software onto your Mac or PC. Some compatible smart home devices to add.A compatible Zigbee USB dongle and/or a Z-Wave enabled USB stick to communicate with devices on that protocol.A clean microSD card with minimum 4GB storage.A Raspberry Pi board - preferably a Pi 3 or Pi 4 with Wi-Fi built-in, but a Wi-Fi dongle should work too.It also enables you to create If This Then That (IFTTT) style rules, a floor plan and use (limited) voice controls. WebThings Gateway allows you to link your existing smart home kit, such as bulbs from Philips Hue however, you can also add Z-Wave and Zigbee USB dongles and connect devices directly, such as a number of off the shelf smart switches, dimmers and sensors, as well as, Ikea and Cree bulbs. The WebThings Gateway allows you to control multiple smart home devices from a simple and secure web portal, which can be accessed at home and remotely. #RASPBERRY PI SMART HOME CONTROL HOW TO#Read next: How to set up and use Home Assistant With the WebThings Gateway (previously known as Mozilla Things), you can build your own home automation server with a Raspberry Pi. While there are plenty of mainstream systems that do this, from Amazon Alexa to Samsung SmartThings, they rely on giving data to big companies. One of the main points of building a smart home is so that you can have a home that’s easier to control and that can react automatically, making your life easier and more convenient. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |